Curated Engineering Evaluation

Intent: Selection between pure unalloyed high-conductivity copper and free-machining tellurium copper for automated screw-machined electrical components.

Engineering Verdict & When to Choose Each

C11000 or tellurium copper: compare accepted electrical parts

By Mat Grades Editorial Desk · Updated 2026-11-14

Consider C14500 when a turned electrical component needs a better machining route, and compare it with C11000 against the same electrical, joining and dimensional requirements. The useful result is cost per accepted component, not a machining rating read in isolation.

Use a trial containing the critical bore, thread and burr-sensitive edge. Measure tool changes, manual finishing and inspection as well as cycle time. Keep the supplied condition in the trial record so that the result can be repeated when the order moves into production.

For the finished connection, evaluate conductor loss and the contact interface separately. Confirm whether any brazing or welding operation is suitable for the selected stock. A faster turning cycle does not qualify an electrical joint, and a conductivity figure does not establish the current rating of the assembled part.

C11000 ETP Copper: evidence to check

C11000 ETP Copper has 199 cataloged property rows. Electrical Conductivity is reported as 101 % IACS (typical; tested at 20 °C). Modulus of Elasticity in Tension is reported as 117210.9 MPa (typical; further condition not stated). The record identifies ASTM B187/B187M; check its scope and ordered edition. These are source-scoped examples rather than unrestricted design allowables. Read the full row context and certificate before using a value for acceptance; an absent value is not zero or a performance failure.

C14500 Tellurium Copper: evidence to check

C14500 Tellurium Copper has 122 cataloged property rows. Electrical Conductivity is reported as 93 % IACS (typical; tested at 20 °C). Modulus of Elasticity (Tension) is reported as 117.2 GPa (typical; further condition not stated). The record identifies ASTM B224; check its scope and ordered edition. These are source-scoped examples rather than unrestricted design allowables. Read the full row context and certificate before using a value for acceptance; an absent value is not zero or a performance failure.

Four questions before approval

  • Does the machining trial include the rejection-prone feature?
  • Are conductivity and contact requirements both defined?
  • Is the joining route qualified for the chosen alloy?
  • Is the quoted cost based on accepted finished parts?

Check the linked material records for the complete source trail. Read the methodology before comparing minimum requirements with typical measurements. No direct substitution or qualified fabrication procedure is implied.

Material Comparison

Compare verified engineering materials side by side with condition-specific mechanical properties.

PDFExcel
Material A (Baseline)
Material B (Comparison)
!
Temper & Metallurgical Context Qualification:The selected records contain different or missing source contexts. Values shown in separate rows are not directly matched. Typical and estimated values are not guaranteed minima; matching context alone does not establish interchangeability.
1. Identity, Classification & Standards
Scroll horizontally for side-by-side comparison
ParameterC11000 ETP CopperC14500 Tellurium Copper
Material FamilyCopper AlloysCopper Alloys
SubfamilyPure CopperFree-Machining Copper
UNS DesignationC11000C14500
COMMERCIAL DesignationElectrolytic Tough PitchTellurium Copper
SPECIFICATION DesignationASTM B187/B187MASTM B224
CDA Designation—Alloy 145
2. Chemical Composition Limits (wt %)Source-specific limits and typical values
Scroll horizontally for side-by-side comparison
ElementC11000 ETP CopperC14500 Tellurium Copper
Cu (Copper)≥ 99.9%≥ 99.9%
P (Phosphorus)—0.004 – 0.012%
Te (Tellurium)—0.4 – 0.7%
3. Physical Properties
Scroll horizontally for side-by-side comparison
PropertyC11000 ETP CopperC14500 Tellurium Copper
Density · TYPICAL · 20 °CUnit: g/cm³8.885–8.941 g/cm³8.941 g/cm³
Specific Gravity · TYPICALUnit: —8.91 —— —
4. Contextual Mechanical PropertiesUnit: SI
Scroll horizontally for side-by-side comparison
Mechanical ParameterC11000 ETP Copper1/2 Hard (H02)C14500 Tellurium Copper1/2 Hard (H02)
Modulus of Elasticity in Tension · TYPICALUnit: 117210.9 MPa 117.2 GPa
Modulus of Rigidity · TYPICALUnit: MPa44126.4 MPa44126.4 MPa
Machinability Rating · TYPICALUnit: %20 %85 %
Forgeability Rating · TYPICALUnit: —65 —65 —
Tensile Strength · Flat Products · 0.04 in · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa289.6 MPa— MPa
Tensile Strength · Rod · 0.25 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa— MPa262 MPa
Tensile Strength · Rod · .0625 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa— MPa262 MPa
Tensile Strength · Rod · 1 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa— MPa289.6 MPa
Tensile Strength · Rod · 1 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa— MPa289.6 MPa
Tensile Strength · Rod · .25 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa— MPa262 MPa
Tensile Strength · Rod · 2 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa— MPa289.6 MPa
Tensile Strength · Rod · 2 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa— MPa289.6 MPa
Tensile Strength · Rod · 0.5 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa— MPa296.5 MPa
Tensile Strength · Rod · 0.5 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa— MPa296.5 MPa
Tensile Strength · Rod · 0.24 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa— MPa296.5 MPa
Tensile Strength · Wire · 0.08 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa— MPa351.6 MPa
Elongation · Flat Products · 0.04 in · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: %14 %— %
Elongation · Rod · 0.25 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: %— %18 %
Elongation · Rod · .0625 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: %— %8 %
Elongation · Rod · 1 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: %— %25 %
Elongation · Rod · 1 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: %— %25 %
Elongation · Rod · .25 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: %— %12 %
Elongation · Rod · 2 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: %— %35 %
Elongation · Rod · 2 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: %— %35 %
Elongation · Rod · 0.5 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: %— %20 %
Elongation · Rod · 0.5 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: %— %20 %
Elongation · Rod · 0.24 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: %— %18 %
Elongation · Wire · 0.08 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: %— %6 %
Shear Strength · Flat Products · 0.04 in · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa179.3 MPa— MPa
Shear Strength · Rod · 0.25 · 1/2 Hard (H02) · TYPICALUnit: MPa— MPa179.3 MPa
Shear Strength · Rod · 1 · 1/2 Hard (H02) · TYPICALUnit: MPa— MPa172.4 MPa
Shear Strength · Rod · 2 · 1/2 Hard (H02) · TYPICALUnit: MPa— MPa172.4 MPa
Shear Strength · Rod · 0.5 · 1/2 Hard (H02) · TYPICALUnit: MPa— MPa179.3 MPa
Shear Strength · Wire · 0.08 · 1/2 Hard (H02) · TYPICALUnit: MPa— MPa186.2 MPa
Fatigue Strength · Flat Products · 0.04 in · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa89.6 MPa— MPa
Yield Strength (0.5% Ext) · Rod · 1 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa— MPa275.8 MPa
Yield Strength (0.5% Ext) · Rod · 1 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa— MPa275.8 MPa
Yield Strength (0.5% Ext) · Rod · 2 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa— MPa268.9 MPa
Yield Strength (0.5% Ext) · Rod · 2 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa— MPa268.9 MPa
Yield Strength (0.5% Ext) · Rod · 0.5 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa— MPa275.8 MPa
Yield Strength (0.5% Ext) · Rod · 0.5 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa— MPa275.8 MPa
Yield Strength (0.5% Ext) · Rod · 0.24 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa— MPa275.8 MPa
Yield Strength (0.5% Ext) · Wire · 0.08 · 1/2 Hard (H02) · TYPICAL · 20 °CUnit: MPa— MPa282.7 MPa
5. Electrical & Thermal Conductive Properties
Scroll horizontally for side-by-side comparison
PropertyC11000 ETP CopperC14500 Tellurium Copper
Electrical Conductivity · TYPICAL · 20 °CCategory: ELECTRICAL • Unit: % IACS101 % IACS93 % IACS
Liquidus Temperature · TYPICALCategory: THERMAL • Unit: °C1082.8 °C1080 °C
Solidus Temperature · TYPICALCategory: THERMAL • Unit: °C1065 °C1051.1 °C
Thermal Conductivity · TYPICAL · 20 °CCategory: THERMAL • Unit: W/(m·K)391.15 W/(m·K)354.8 W/(m·K)
Coefficient of Thermal Expansion (68-212°F) · TYPICALCategory: THERMAL • Unit: µm/(m·K)16.92 µm/(m·K)17.1 µm/(m·K)
Coefficient of Thermal Expansion (68-392°F) · TYPICALCategory: THERMAL • Unit: µm/(m·K)17.28 µm/(m·K)17.46 µm/(m·K)
Coefficient of Thermal Expansion (68-572°F) · TYPICALCategory: THERMAL • Unit: µm/(m·K)17.64 µm/(m·K)17.82 µm/(m·K)
Specific Heat Capacity · TYPICAL · 20 °CCategory: THERMAL • Unit: J/(kg·K)385.2 J/(kg·K)385.2 J/(kg·K)
Annealing Temperature Range · RANGECategory: THERMAL • Unit: °C371.1–648.9 °C426.7–648.9 °C
Hot Working Temperature Range · RANGECategory: THERMAL • Unit: °C760–871.1 °C760–871.1 °C
6. Hardness Evaluation (Discrete Scales Preserved)No cross-scale mathematical conversion
Scroll horizontally for side-by-side comparison
Hardness ScaleC11000 ETP CopperC14500 Tellurium Copper
Rockwell B Hardness · Flat Products · 0.04 in · 1/2 Hard (H02) · TYPICAL · 20 °C40 HRB—
Rockwell B Hardness · Rod · 0.25 · 1/2 Hard (H02) · TYPICAL—43 HRB
Rockwell B Hardness · Rod · 1 · 1/2 Hard (H02) · TYPICAL—42 HRB
Rockwell B Hardness · Rod · 0.5 · 1/2 Hard (H02) · TYPICAL—43 HRB
Rockwell F Hardness · Flat Products · 0.04 in · 1/2 Hard (H02) · TYPICAL · 20 °C84 HRF—
Rockwell 30T Hardness · Flat Products · 0.04 in · 1/2 Hard (H02) · TYPICAL · 20 °C50 HR30T—
Rockwell 30T Hardness · Rod · 0.5 · 1/2 Hard (H02) · TYPICAL—50 HR30T
7. Fabrication & Processing Comparison
C11000 ETP Copper Characteristics:

Machinability: Machinability rating: 20% relative to free-cutting brass (C36000 = 100%). Forgeability rating: 65.

Weldability: Soldering: Excellent; Brazing: Good; Butt Welding: Good; Gas Shielded Arc Welding: Fair; Oxyacetylene Welding, Coated Metal Arc Welding, Spot Welding, and Seam Welding: Not Recommended.

Formability / Cold Working: Capacity for being cold worked: Excellent; Capacity for being hot formed: Excellent.

Heat Treatment & Annealing: Annealing temperature range: 371.1°C to 648.9°C (700°F - 1200°F). Hot working temperature range: 760.0°C to 871.1°C (1400°F - 1600°F).

C14500 Tellurium Copper Characteristics:

Machinability: Machinability rating: 85% relative to free-cutting brass (C36000 = 100%). Forgeability rating: 65.

Weldability: Soldering: Excellent; Brazing: Good; Oxyacetylene Welding: Fair; Gas Shielded Arc Welding: Fair; Coated Metal Arc Welding: Not Recommended; Spot Weld: Not Recommended; Seam Weld: Not Recommended; Butt Weld: Fair

Formability / Cold Working: Capacity for Being Cold Worked: Good. Capacity for Being Hot Formed: Good.

Heat Treatment & Annealing: Annealing temperature range: 426.7°C to 648.9°C (800°F - 1200°F). Hot working temperature range: 760.0°C to 871.1°C (1400°F - 1600°F).